dip h hC 16 dimensions are shown: inch (mm) specifications and dimensions subject to change www.ck-components.com specifications switch function: spst - 1 thru 12 position available (except 11 position). cont act rating: carry: 100 ma max. @ 50 v dc. switch: 100 ma max. @ 5 v dc or 25 ma max. @ 25 v dc. mechanical and electrical life : 10,000 make-and-break cycles at full load, each circuit. contact resistance: below 50 milliohms typ. initial @ 2-4 v dc 100ma. insula tion resistance: 10 9 ohms min. dielectric strength: 500 v rms min. @ sea level between adjacent terminals. capacitance: 5pf max. between adjacent terminals. storage & operating temperature: -40c to 85c. shock : withstands 20g 11 ms sawtooth waveform with no con - tact opening gr eater than 10 microseconds. quantity part number no.pos. dim. a dim. b per tube bd01 1 .180 (4,57) na 115 bd02 2 .280 (7,11) .100 (2,54) 74 bd03 3 .380 (9,65) .200 (5,08) 54 bd04 4 .480 (12,19) .300 (7,62) 43 bd05 5 .580 (14,73) .400 (10,16) 35 bd06 6 .680 (17,27) .500 (12,75) 30 BD07 7 .780 (19,81) .600 (15,24) 26 bd08 8 .880 (22,35) .700 (17,78) 23 bd09 9 .980 (24,89) .800 (20,32) 21 bd10 10 1.080 (27,43) .900 (22,.86) 19 bd12 12 1.280 (32,51) 1.100 (27,94) 16 schematic spst bd series standard profile dip switches vibration: no contact opening greater than 10 microseconds and no contact closure when exposed to vibration .06 in da or 5g, whichever is less, from 10 to 55 hz, and 10g from 55 to 500 hz. solderability: per mil-std-202f method 208d, or eia rs-186e method 9 (1 hour steam aging). p ackaging: switches supplied in rigid dispensing tubes in full-tube quantities only: this may ef fect or der quantity. number of switches per tube varies with model. switch position 1 denotes pin number 1. all switch actuators in ff?osition, standard. materials case & cover: glass filled polyester (pbt), flame retardant (ul 94v-0). actuator: glass filled nylon 6/6, flame retardant, heat stabilized (ul 94v-0) contacts: gold over nickel over phosphor bronze. terminals: matte-tin over nickel over phosphor br onze. note : specifications and materials listed above ar e for switches with standar d options. for information on specific and custom switches, consult customer service center . features/benefits ? t raditional full profile dip switch ? extended actuator for easy actuation ? open bottom construction allows for solder washing without the need for tape seal ? rohs compliant vertical full profile dip bd08 .030 (0,77) .160 typ. (4,06) .006 (0,16) .380 (9,65) .100 typ. (2,54) .020 typ. (0,51) .265 (6,73) .141 typ. (3,58) .089 (2,26) .297 (7,55) ?038 typ. (0,97) .100 typ. (2,54) dim '? dim ' .297 (7,55) .032 (0,82) typ. .080 typ. (2,03) 1 2345678 o n .062 (1,58) max actua tor travel (1,5) .059 typ. t ypical applications ? address switch for industrial controls ? logic switching for computers and peripherals ? function controlling for numerous applications
dip h hC 17 dimensions are shown: inch (mm) specifications and dimensions subject to change www.ck-components.com 8 7 6 4 3 2 1 on 0.050 (1,27) .089 (2,26) 0.061 typ. (1,55) 0.030 (0,77) 0.297 (7,55) .100 (2,54) .020 typ. (0,51) .100 typ. (2,54) .010 (0,25) .006 (0,16) dim.a .380 (9,65) .046 dia typ . (1,17?) .100 (2,54) .100 typ. (2,54) .080 (2,03) .032 (0,82) typ. 5 .320 (8,12) .125 (3,18) quantity part number no.pos. dim. a per tube bd02av 2 .280 (7,11) 72 bd03av 3 .380 (9,65) 52 bd04av 4 .480 (12,19) 42 bd05av 5 .580 (14,73) 35 bd06av 6 .680 (17,27) 29 BD07av 7 .780 (19,81) 26 bd08av 8 .880 (22,35) 23 bd09av 9 .980 (24,89) 20 bd10av 10 1.080 (27,43) 18 bd12av 12 1.280 (32,51) 15 schematic spst bd series standard profile dip switches open base and av right angle terminal style installation, soldering and cleaning all bd series standard profile dip switches can be hand soldered or machine soldered without the use of boot, caps, tapes or special attention. open base washable models have unique design, allowing solvent cleaners and water/deter gent solutions to flush and clean the electrical contacts of the contaminants and fluxes. for best results, follow these directions: 1) wave soldering recommended at 500 f (260o) solder temperature. 2) hand solder using 30 watt small tip iron controlled at 500 f (260o), 10 seconds max./terminal. 3) open base washable models: clean flux using forced rinse, high agitation or triple bath cleaning method. do not mask or cover switch in any way during cleaning. switch is designed for easy solvent flush out. 4) all switch actuators must be in ff?osition during soldering and cleaning processes. bd08av
|
